οδηγίες χρήσης SILVERCREST SFW 250 B1

[. . . ] KITCHEN TOOLS CY Mincer SFW 250 B1 CY Mincer Operating instructions xav CY KOMPERNASS GMBH BURGSTRASSE 21 · D-44867 BOCHUM www. kompernass. com ID-Nr. : SFW 250 B1 10/11-V2 IAN: 71981 SFW 250 B1 1 2 e 3 w q 0 9 87 6 5 4 Index Introduction . 2 Information for these operating instructions . Assembling the sausage stuffer attachment . 16 SFW 250 B1 1 GB IE CY Introduction Information for these operating instructions These operating instructions are a component of the Meat Grinder SFW 250 B1 (henceforth designated as the appliance) and they supply you with important information about the intended use, safety and connection as well as operation of the appliance. [. . . ] 3) Pull one end of the sausage skin (natural or artificial sausage skin) onto the sausage stuffer attachment q and tie a knot in the other end. For 1 kg of the filling, you will need approximately 1. 60 m of sausage skin. SFW 250 B1 9 GB IE CY TIP!Soak the natural sausage skin in lukewarm water for about 3 hours before using it and wring it out before attaching it. This will make the natural sausage skin more elastic. Natural sausage skins are available from butcher suppliers close to slaughter houses or from your family butcher. 4) The sausage mixture will be pressed into the sausage skin by the sausage stuffer attachment q. When it is long enough switch the appliance off, press the sausage together at the ends and rotate it a couple of times along its longitudinal axis. Sausage meat tends to expand when cooked or frozen. Therefore, to prevent it from bursting it is best not to overstuff the sausage. 5) When you have read and understood all of the instructions on the topic "Sausage", you can now use the appliance as described in the chapter "Operating the appliance". Using the kubbe attachment With the kubbe attachment e foodstuffs can be processed to form hollow rolls of meat or vegetables, which can then be stuffed as desired. 1) First put the meat through the meat grinder twice before pressing it through the kubbe attachment e. 2) When you have read and understood all of the instructions on the topic "Kubbe-Attachment", you can now use the appliance as described in the chapter "Operating the appliance". Making biscuits After you have made the biscuit pastry according to your recipe, and after having fixed the biscuit attachment 1: 1) When you have read and understood all of the instructions on the topic "Biscuits", you can now use the appliance as described in the chapter "Operating the appliance". 2) Line a small baking tray with greaseproof paper and place or hold it directly under the exit opening at the front of the appliance. 3) Press pastry evenly into the meat grinder casing 5 ­ the transport screw 6 then pushes it through the selected design on the design motif strip of the biscuit attachnment 1. 4) When the biscuit is the required length, stop the appliance and break the pastry off at the exit opening. Lay the biscuits on the baking tray. 10 SFW 250 B1 Non-functionality If the drive is blocked by accumulated food: Press the button "0" to stop the meat grinder. Press and hold the button "<". The appliance will now run in the reverse direction. This enables you to transport the food which has become stuck a short way backwards, and the motor to run freely again. When the drive runs smoothly again, release the "<" button. Press the button "I" to re-start the meat grinder. If you do not succeed in getting the drive free with this, clean the appliance as described in the chapter "Cleaning". GB IE CY Should the motor suddenly stop, it could be due to automatic activation of the internal overload fuse. [. . . ] 8) 5 " ". 22 SFW 250 B1 Kubbe - . 4) Kubbe e Kubbe e 5. 6) 5 " ". GR CY - . 6) , 0 . SFW 250 B1 23 7) 1 1. [. . . ]